ASTM B221-08 PDF

      No Comments on ASTM B221-08 PDF

Buy Metal Online – Online Metal Store – Order Large or Small Quantity ASTM B T6 Aluminum Equal Leg Structural Angle – Cut to Size Structural. Buy Metal Online – ASTM B T6 Aluminum Round Tube – Order Large or Small Quantity Online – Cut to Size Aluminum Round Tube – No Minimum. Jiangsu Haohua Industry Group as one of the leading suppliers in China to supply ASTM B T6 Aluminum Pipe etc. [Contact person:Ms chris ; Email.

Author: Doutaxe Kajizshura
Country: Samoa
Language: English (Spanish)
Genre: Environment
Published (Last): 11 June 2012
Pages: 113
PDF File Size: 6.70 Mb
ePub File Size: 14.15 Mb
ISBN: 484-7-71655-351-8
Downloads: 15888
Price: Free* [*Free Regsitration Required]
Uploader: Moogubar

ASTM B221-08 6061-T6 Aluminum Bar Steel Round Bars / Tubes For Stakes , Tines

Unalloyed aluminum contains a minimum of As much of the rejected material as possible shall be returned to the producer or supplier by the purchaser. NOTE 4—It is difficult to obtain a reliable analysis of each of the components of clad materials using material in its? Sampling shall be atm accordance with Practice E A number in parentheses indicates the year of last reapproval. NOTE 1—Throughout this speci?

ASTM B221-08 PDF

NOTE 3—It is standard practice in the United States aluminum industry to determine conformance to the chemical composition limits prior to further processing of ingots into wrought products. For the products described, mechanical property limits for the respective size ranges are based on the analyses of at least data from standard production material with no more than ten 2b21-08 from a given lot. A designation not in con?

On approval of the purchaser, however, the producer or the supplier may use a system of statistical quality control for such examination.

  LF444 DATASHEET PDF

Due to the continuous nature of the process, it is not qstm to keep a speci? The electrical conductivity shall be determined in accordance with Practice E in the following locations: M Composition of cladding alloy applied during the course of manufacture. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

Chemical milling may be used on? For small sizes of tubes, a cut-out portion may be? J Minimum yield strength for tube, X, and so forth A2.

ASTM B PDF – $ : : National Standards Institute Documents Download Store

Current edition approved Oct. Marking for shipment of such material shall be in accordance with Fed. F The aluminum content shall be calculated by subtracting from G Material in the T42 and T62 tempers is not available from the material producers. Tensile Properties of Material from the Producer 8. Elongation of cut-out round specimens is measured in 43 specimen diameter. The correctness of cladding alloy used can usually be veri?

K Yield strength is not applicable in tube. Weight, max per Piece, lb Max Width: The producer may use his own or any other suitable facilities for the performance of the inspection and test requirements speci? C Elongation of full-section and cut-out sheet-type specimens is measured in 2 in. If the chemical composition has been determined during the course of manufacture, analysis of the?

E Other Elements—Total shall be the sum of unspeci?

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The purchaser shall have the right to perform any of the inspections and tests set forth in this speci? T62G 5 H up through 25 over 25 through 32 up through 32 2. Other methods may be used only when no published ASTM test method is available. ASTM International takes no atsm respecting the validity of any patent rights asserted in connection with any item mentioned in this atm.

  EKSANTEMA SUBITUM PDF

E These alloys are also produced in the F temper for which no tensile properties are speci? Any requirement not so covered is subject to negotiation between the producer and purchaser.

All tests are performed in accordance with the appropriate ASTM test methods. However, such analysis is not required and b221-088 not cover all metallic Others elements.

However, should subsequent testing by the purchaser establish that the material does not meet these requirements, the material shall be subject to rejection. Rod, Bar and Pro? Each sample shall be taken from material considered acceptable in accordance with the lot-acceptance criteria of Table 4. A minimum of three adjacent replicate specimens shall be taken from b2221-08 sample and tested. The producer may analyze samples for trace elements not speci?

For a tube having a diameter larger than can be properly mounted for polishing and examination, the portions of the cross section polished for examination may consist of an arc about 1? Heat Treatment and Reheat-Treatment Capability